Ford c1 axle code.

All 99 F250 7.3 with either trans have a Ford/Visteon "Sterling" rear axle with 10.5" ring gear and 3.73 axle ratio. So the only question is whether you have LS or not. The axle code on the Federal Certification Label on the lower doorpost behind the driver's door will begin with either a number or a letter.Sep 4, 2019 ... Here's a simple way to check your abs or wheel speed sensors on your car or truck. I'll show you the complete diagnosis and repair so that ...I have a question on a rear axle swap for my 2004 Ford Excursion Diesel, what is the difference in rear axles? Obviously there's a difference between limited slip and not, but what are the differences in the other codes? I have axle code: C1 — 3.73 limited slip, F-250/Excursion This car is for resale, so I do not care if it is limited slip or ...Likes: 0. Received 5 Likes on 5 Posts. How to decifer door jam codes on F250? C1 = 3.73 limited slip, F-250/Excursion. 9 = Four-speed automatic overdrive (4R100) KB = just a code for the suffix for the part numbers of the springs....doesn't tell you anything else. RC = region code but I cant find what the 72 means.1987 - 1996 F150 & Larger F-Series Trucks 1987 - 1996 Ford F-150, F-250, F-350 and larger pickups - including the 1997 heavy-duty F250/F350+ trucks. Sponsored by: 1996 F250 4WD Axle Code "C5" ? Reply ... the C5 axle code means you have 4.10 gears, and a limited slip differentail . Reply Like #4 ...

Overview. Dexter, a premier manufacturer and distributor of axles, suspension, brakes, doors, venting products, trailer parts and accessories, and towing components serving …Clutch, Transmission, Differential, Axle & Transfer Case - what gear ratio is with C7 axle code? - I have an 80 F250. The rear is 10 bolt. I believe it is Dana 60 since I see the 60 casting on the RH side axle shaft housing. The tag is all rusted and unreadable. Is there a website with all of the axle codes listed or...

I'm planning on changing out the front and rear differential fluid in my Ranger and I have kind of a noob question. My truck has axle code R7. I've read that the R7 is an 8.8" L/S 4.10 ratio axle. My owner's manual states to add 4 oz of friction modifier XL-3 to the rear diff. for Traction-Lok axles along with 80w-90 fluid.Here is a list of the most frequently seen Ford rear axle codes along with their corresponding gear ratios and axle types: Code Gear Ratio Axle Type; AB: 3.55: Limited Slip: H9: 3.73: Open: B6: 3.31: Limited Slip: 3L: 3.15: Open: Identifying Ford Rear Axles from Door Stickers Locating the Door Sticker on a Ford Vehicle.

Ford Truck Enthusiasts Forums. Super Duty/Heavy Duty. 1999 to 2016 Super Duty. Rear axle code 37 on door jamb? 1999 to 2016 Super Duty 1999 to 2016 Ford F250, F350, F450 and F550 Super Duty with diesel V8 and gas V8 and V10 engines.My E99 has axle code of 31, which checks out to be an open 3.73 for an F-250. I am eyeing up two different trucks, one with C1 axles and one with a D1 axles. …99-01 had the Dana 50, late 01-now have the Dana 60. 1999 to 2016 Super Duty - Front axle codes vs. Rear axle codes - I'm struggling a bit to find codes for my front axle.. I see a lot of info about rears but not much about fronts.Rear Axles Used: Ford 7.5-Inch Axle: 1983-2011 Ford Ranger’s without a 4.0L V6 came with the Ford 7.5-Inch Axle. 1998-2011 Ford Ranger Super Cab 4×4’s are frequently equipped with 8.8-Inch axles regardless of engine size. Click HERE for more Ford 7.5-Inch Information & Specifications.

Yukon Master Overhaul Kit 1999-2007 Ford 10.5" Ford 10.5" $ 630.89 2050-01-01. Power Products carries the Yukon Master Overhaul Kit Ford 10.5" Yukon Gear Dana 80 35 Spline Axle Shaft , 40.24" Long , 8 X 4.02" Bolt Pattern Dana 80 35 Spline AXL YUK-YA_D47847-2 19.42 Yukon Gear & Axle YA D47847-2.

Mar 14, 2011 · Excursion - King of SUVs - Axle codes? Strange find! - I have found a possible purchase but I'm told the door sticker has an axle code of C0 rather then any of the following. 31 — 3.73 non-limited slip, F-250/Excursion C1 — 3.73 limited slip, F-250/Excursion 32 — 4.10 non-limited slip, F-250 C2 — 4.10 limited slip,...

Accurate Differential Identification is the first and most important step in your differential repair, upgrade or overhaul project. The following information is provided to help you identify the differential you are working on. If in doubt, consult one of our differential experts at (800)510-0950! Professional technical support is available ...The third character is for the vehicle model code. For example, R3 is Mustang, H7 is F-Series Short Cab, L3 is F150/250. So a 2011 Mustang axle is part number BR3W-4001-KH. The last character designates …Below the bar code, you will see the word AXLE and a two-digit code. Use this chart to find the axle ratio that corresponds to that code: Axle Code 71 = 3.73 Gear Ratio (Non-Limited Slip) Axle Code 73 = 3.73 Gear Ratio (Limited Slip) Trying to figure out what axle ratio is in your 2019 Ford Ranger and whether or not it's a limited slip? This ...RPM's don't tell you though if you have a LS or not...you need the code for that. 31 — 3.73 non-limited slip, F-250/Excursion C1 — 3.73 limited slip, F-250/ExcursionSep 4, 2019 ... Here's a simple way to check your abs or wheel speed sensors on your car or truck. I'll show you the complete diagnosis and repair so that ...

3L isn't on the list I have from a specs doc from Ford. Here is all the axle codes I found for '05. ... 4n, axle, c1, code, codes, d1, d2, duty, e3, ew, f250, f350 ...The code appears as a number or letter/number combination in the 'Axle' column of the label. If you look at the 'AXLE' section on the label above, you'll see that this Ranger has a 'F7' axle code. Using the chart below, we know that this axle is a 7.5-Inch axle with a 4.10 limited slip. Axle codes for Ranger, Bronco II, Explorer and Aerostar ...Feb 17, 2010 · What "axle" code is on the sticker on the drivers side door pillar? Find the code on the sticker then read the list below to find the gear info. Rick...-----Axle Type 31 — 3.73 non-limited slip, F-250/Excursion C1 — 3.73 limited slip, F-250/Excursion 32 — 4.10 non-limited slip, F-250 C2 — 4.10 limited slip, F-250/Excursion A: The Ford axle code 4N is designed to improve fuel efficiency by allowing the engine to operate at lower RPMs while maintaining appropriate torque output. Lower RPMs mean less fuel consumption, making it beneficial for those who prioritize fuel efficiency.Common rear end axle codes for Ford vehicles. Ford vehicles have different rear end axle codes depending on the model and year of manufacture. Some common rear end axle codes for Ford vehicles include “C6” for a 3.55 gear ratio, “F6” for a 3.73 gear ratio, and “H9” for a 4.11 gear ratio. It is essential to consult the specific axle ...

C7TA-BV = 1967 F250 Dana 60 / 4.10-1 / non Limited Slip / Ring gear has 29 splines (1965: 10 splines). 5 12 7C1 / Assembled May 12, 1967 / C1 is the code for the assembly plant. The fact that the rear axle ID tag is still there...is somewhat amazing, as most are missing by now. There are two possible reasons why:The Ford Axle Code L9 refers to a specific axle ratio used in Ford vehicles. In this section, we will explain what the L9 code stands for, its significance, and how it affects the performance of the vehicle. The L9 code typically represents a 3.73 axle ratio. The axle ratio indicates the number of times the driveshaft must rotate for the wheels ...

The Ford 3E axle code can have a significant impact on the performance and capabilities of a Ford vehicle. The 3E code represents specific gear ratios and differential types, which can influence factors such as towing capacity, acceleration, and fuel efficiency. By understanding the 3E axle code, drivers can make more informed …Feb 7, 2011 · Axle Code Information Jump to Latest Follow 36K views 10 replies 4 participants last post by Cat_Rebel Feb 8, 2011 The code can be found on the Vehicle Identification Number (VIN) label, which is typically located on the driver’s side door jamb or the front windshield. 2. Decoding the Axle Code. To decode the Ford Axle Code, you need to refer to the manufacturer’s specifications or consult an online decoding tool. The code is made up of several ...1999 to 2016 Super Duty - axle codes - Hi guys, I tried searching the forum first for any info that telles me the axle codes on the inside door sticker for 1999 + superduties (particularly with Diesel) ie. C1, etc...thanks for your help! -CharlieFord’s F-150 pickup truck is about as American as a vehicle can get. Ford’s F-150 pickup truck is about as American as a vehicle can get. Not only has the iconic truck been the cou...Trailer axles sitting out-of-square can cause a trailer to travel at an angle when towed. The travel angle increases the wear rate of the tires attached to the axles, or worse, cau...Here is a list of the most frequently seen Ford rear axle codes along with their corresponding gear ratios and axle types: Code Gear Ratio Axle Type; AB: 3.55: Limited Slip: H9: 3.73: Open: B6: 3.31: Limited Slip: 3L: 3.15: Open: Identifying Ford Rear Axles from Door Stickers Locating the Door Sticker on a Ford Vehicle.

To decode Ford 8.8 axle codes, locate the axle tag or check the stamping on the axle housing. Then, use Ford’s axle code chart or online resources to match the code with its corresponding specifications. This will provide valuable information about the axle’s characteristics. Decoding the axle codes correctly is crucial to ensure ...

They were the 450s of the OBS, 2wd with a leaf spring mono beam axle on the front like a semi. Straight narrow frame with a 10 lug Dana 80 with disc brakes & hydro boost. Geared to the moon, they came with 4x4 E4OD or ZF5 trannys & had a parking brake that bolted onto the rear of the tranny inside of in the axle itself.

What is the Ford Axle Code C1? The Ford Axle Code C1 refers to a specific axle ratio configuration used in Ford vehicles. It is important for understanding the gear ratio and performance characteristics of the vehicle. The Ford Axle Code C1 is a crucial factor in determining the performance and towing capabilities of a Ford vehicle.Dec 23, 2017 · So here, thanks to Mike and ND, is the corrected graphic on decoding the axle tag on dents with 9" rear axles. 5MB: The 5 refers to the fifth year, M refers to December and B refers to the second week of that month. Thus, the date of manufacture is Second Week (day 8-12) of December, 1975. Ford Rear Axle Assembly Identification - Page 01: NOTE: Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: WBG-E : Ford Truck '63-71 F100: 3.70: 9 in: NL: 28-WBG-F : Ford Truck '63-71 F100:There are several common Ford rear axle codes that indicate different specifications. For example, the “C6” code represents a 2.73:1 ratio and is commonly found in vehicles optimized for fuel efficiency, while the “D2” code signifies a 4.10:1 ratio and is often used in trucks for better towing capabilities. Understanding the meaning ...In the Ford Explorer, some common axle codes include: 31 – 3.27 gear ratio with an open differential. V6 – 3.27 gear ratio with a limited-slip differential. 55 – 3.55 gear ratio with an open differential. C7 – 3.73 gear ratio with a conventional differential. L9 – 3.73 gear ratio with a limited-slip differential.Received 648 Likes on 543 Posts. The AXLE code on the Certificaton Label is 53 but...in the Ford truck parts catalog, this refers to two different Dana 70's. 53: 1980/85 Dana 70 H/D / 4.56-1 / No Limited Slip / 7,400 lbs. Rear Axle Capacity. 53: 1983/89 Dana 70 or Dana 70U / 3.54-1 / No Limited Slip / 7,400 or 7,800 lbs. Rear Axle Capacity.C7TA-BV = 1967 F250 Dana 60 / 4.10-1 / non Limited Slip / Ring gear has 29 splines (1965: 10 splines). 5 12 7C1 / Assembled May 12, 1967 / C1 is the code for the assembly plant. The fact that the rear axle ID tag is still there...is somewhat amazing, as most are missing by now. There are two possible reasons why:The “3” represents the axle type, while the “L” indicates the presence of a limited slip differential. Example 2: B6. For this example, the axle code corresponds to a Ford truck with a 3.55 axle ratio and a non-limited slip differential. The “B” represents the axle type, and the absence of an “L” indicates a non-limited slip ...So here, thanks to Mike and ND, is the corrected graphic on decoding the axle tag on dents with 9" rear axles. 5MB: The 5 refers to the fifth year, M refers to December and B refers to the second week of that month. Thus, the date of manufacture is Second Week (day 8-12) of December, 1975.1999 - 2003 7.3L Power Stroke Diesel - C1 axle - I am in the middle of changing oil in my rear differential. I just want to be positive my axle is limited slip. It is labeled as C1, but there is are no L in any of the descriptions.

F250 ford powerstroke 1999 code zf manual axle 3l turbo diesel 2002 c1 truck parts source2002 ford f250 axle code c1 Axle ratiosAxle code 1986 ford f250 b93 trucks. Axle f250Axle ford f250 code c1 2004 source Identification ford axle code chartAxle f150 ratios bullnose garagemahal.May 19, 2003 ... Rear Axle Code is stamped on the axle housing. ... QS 06 01 C1 is the stamping, I added an ... 1968 Chevelle Malibu, 327 L30, 3 speed on the tree, ...Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: V106A: Ford F250 Pickup 85-86: 3.55: 10.25: NL--V106BInstagram:https://instagram. hemby willoughby funeral home tarboro ncmissouri 4 inch soil temperature mapchamberlain university redditgangster lowrider tattoos One crucial piece of information provided by the Ford Axle Code 3J is the gear ratio of the axle. The gear ratio determines the number of turns the driveshaft needs to make for each turn of the wheels. It affects acceleration, towing capacity, and fuel efficiency. Look for the code prefix “39” to identify the specific gear ratio.Assuming your truck is original it'll tell you the axle code and then reference this to find what it translates to: Here's the snippet from the link above, just to save a little searching. There's a sticker on the backside of front axle. There you should see 3.73. devoted cvs otcosceola county arrest reports Ford Rear Axle Assembly Identification - Page 13 ... Axle tag location and appearance may vary by application. Code Application Ring Gear And Pinion NL or L Axle Shaft Splines Additional Information; Ratio: Diameter of RG: S406-B: Ford F250SD, F350SD Pickup ‘99: 3.73: 10.50: NL--S406-C: Excursion '00 Ford F250SD, F350SD Pickup ‘99-01:I found out that in the 70's it was the 3.25 gearing. Clutch, Transmission, Differential, Axle & Transfer Case - Axle Code 17??? - Well I finally got around to checking the door plate on my truck and it does match the VIN # although I can find no sign of a dash VIN plate to be 100% sure of the VIN. kobe bryant daughter autopsy report Below the bar code, you will see the word AXLE and a two-digit code. Use this chart to find the axle ratio that corresponds to that code: Axle Code 71 = 3.73 Gear Ratio (Non-Limited Slip) Axle Code 73 = 3.73 Gear Ratio (Limited Slip) Trying to figure out what axle ratio is in your 2019 Ford Ranger and whether or not it's a limited slip? This ...Trailer axles sitting out-of-square can cause a trailer to travel at an angle when towed. The travel angle increases the wear rate of the tires attached to the axles, or worse, cau...